KS-SF22R |
| Home | Instructions | KS-SF22R | |
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. NOTE 2: Any changes or modifications to this unit ot expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. • External: Domineering power with tiger form styling and safeguard device to motorbike or bicycle. 1. External Structure FigureCautions: Remote control have two below types according to order package set. Figure of bottom cover removal method WL03C:
Figure of bottom cover removal method WL09C:
2. Installation Guides2.1 Host battery replacement and installation. 2.1.1. Factory will install the battery by default. If the battery requires a replacement or installs new batteries, please follows below figures method by open bottom cover, install 3 pes AAA alkaline battery. Dismantle bottom cover method figure:
Remove the host's 1pc bottom screw and use minus (-) screwdriver to open bottom cover by rotate or turn around. After open the bottom cover, continue to open side of the cover until it is easily dismantled by hand. If do not have minus (-) screwdriver, can try use a solid film or shim to open as show in above figure. 2. 2. Application and Setting 2.2.1. ARM & DISARM 2.2.1.1. Press once time on remote control [ ] key in standby mode, the host produces "Do..Le..Mi" sound and enter into ARM mode,after 5 seconds, a 'Bi' sound and enter into alert mode. Any touch or hit is occurred at ARM alert mode, the host will trigger the alarm immediately for 2 seconds, detect on any touch or hit again within 2~ 12 seconds, the alarm will continue for 30 seconds (one ringtone type for 2 seconds alarm; 6 ringtones types for 30 seconds with automatic switching). 2.2.1.2. Press remote control [ ] key once at alert situation, the host will produces once "Mi..Le..Do" sound and signals the host was exited from alert mode already. 2.2.1.3. When the host is still alarming, direct press remote control DISARM key to stop and exit from ARM mode simultaneously. 2.2.2. Touch Sensivity Level, Volume, SOS setting feature. 2.2.2.1. Touch sensivity has 7 levels from high to low, 7 ringtones sound prompt, Do, Le, Mi, Fa, So, La, Di; Volume has 3 levels.high, medium and low. 2.2.2.2. SOS is an internationally popular feature and off mode at factory default setting. Note that the SOS function will recognize the installation state of the host.so please do not change the installation direction again after complete the installation, otherwise it may cause the function to fail or be abnormal. After the SOS function is turned on, it will automatically call of when the bicycle is tilted more than 45 degrees by accidentally. After corrected back the bicycle to the original position, it will turn off the call of automatically.The SOS trigger sound is in accordance with international conventions/standards. 2.2.2.3. Setting method. * To adjust the sensitivity level, press [ ] key continuously from high to low in cycle with seven adjustable levels. 2.2.2.4. The host changes the batteries, sensitivity level and volume setting momeries will be stored. Because of SOS may needs to recalibrate, so it will automatically turn off. 2.2.3. Bell Ringtone switching function. 2.2.4. Bell and search function: Press bell key and trigger selected bell ringtone to find the motorbike/bicycle easily. 2.2.5. Remote control Learning Code 2.2.5.1. The first remote control code learning method: At first, remove the host batteries and install back after 30 seconds. Long press remote control [ ] key to enter the code learning mode. After the host produces once "Bi" sound, press ARM or DISARM key with twice "BL.Bi.." sound, you should able to use new added remote control already. 2.2.5.2. To add more remote controls code learning method: Press old remote control's DISARM key to disarm at first, then, long press at old remote control [ ] to enter code learning mode. After once 'Bi' sound, press new remote control' s ARM or DISARM key with twice "Bi ... Bi" sound, you should able to use new added remote control already. 2.2.5.3. Decoding method: Be cautious when use this function! At first, confirm the host is not at ARM mode; Long press for coded remote control [ ] key to enter into the code learning mode. After once 'Bi' sound, press [ ] key with "Bi ... Bi ... Bi" 3 times sound, the host will delete all coded addresses. Please refer to above method for new code learning. 2.2.5.4. Be cautious of the host can caters up to 8 remote controls coding only, the first registered remote control coding will be removd if exceeds 8 remote controls registration. 2.2.6. Battery low power indication. 2.2.6.1. When the host is at low battery (3.3V) condition, a weak "Du..Du.." 2 times sound was generated when use ARM or DISARM and requires to replace the battery immediately. 2.2.6.2. When the remote control's flashlight becomes dark/fade or remote control range becomes shorter, it indicates the battery power is low and replaces with a new battery accordingly. 3. Operating Guides.3.1. The host uses 3 pcs AAA alkaline battery, normal usage 1-3 months; |
| EN | DE | FR | RU | |
ks-sf22r |
---|
© «Org-Info.Mobi» |