 Radio-controlled ship Heng Tai landing ship Wasp 1: 350 2.4G - HT-3833BRadio-controlled ship Heng Tai landing ship Wasp 1: 350 2.4G - HT-3833B is a collectible mini-version (scale 1: 350) of the Military Affairs ship. The model is controlled by a fully functional remote control with a range of 80 meters. The ship is equipped with a powerful electric motor that controls the propeller.
Specifications
Product size: 74.5x23x14 cm
Speed: 6 km/h
Operating distance: about 80 metres
Charging time: 150 minutes
Suitable age: above 14
Battery: 9.6V 800mA
USB charger: 9.6V 300mA
Using period: about 25 minutes
Frequency: 2. 4GHz
Basical function: forward / backward, turn left / right
Instruction of remote controller  
1. Put the ship on the water, turn on the power switch of remote controller. The LED light of remote controller will be flashing by flashing, then stop flashing, that means match the code successfully.
2. Pull the control bar of remote, the ship will be forward. Push the control bar of remote, the ship will be backward.
3. Turn the knob of remote be forward, the ship will be turn left. Turn the knob of remote be backward, the ship will be turn light. Part assembly instruction  
1. Insert the spare parts of the radar device into the plughole on the shipbody, then press them tightly with fingers. (As Pic. 1 shows)
Accessories: 2 piece of radars 2. Insert the deck into the plughole on the shipbody, then press it tightly with fingers. (As Pic.2 shows)
Accessories: 2 piece of decks. 3. Insert the helicopter into the plughole on the shipbody, then press it tightly with fingers. (As Pic.2 shows)
Accessories : 1 piece of helicopter.
Insert the cannon into the plughole on the shipbody, then press it tightly with fingers. (As Pic.2 shows)
Accessories: 1 piece of cannon. Preparation before using 1. Install the battery of remote controller.
Open the battery-cover on the remote controller, assemble 3 pieces of 1.5V AA battery according to the mark of positive negative pole, then equip the battery-cover. 2. Wrest the knobs on the cabin and battery cover of the ship, take battery cover away and put the batteries into the battery holder. Connect the plug on the batteries with the plug on the battery holder. How to give a function demonstration Install the battery of remote control and ship firstly. Keep the finger wet, there is a «TOUCH SWITCH» on the deck ( as Pic. 2 shows), touch it by finger for close circuit. Then operate the controller to give a function demonstration. Caution:
1. It is no need to touch the "TOUCH SWITCH" when the ship is playing on the waterjust operate the controller to radio control the ship;
2. Please don't touch the screw propellers when they're working.
3. Do seal the vent when operating the ship. Replace battery Attention:
1. The battery should be dedicated battery designated by our factory.
2. The battery should be put in the right place. Instruction of battery and charger Instruction or charging:
1. Open the battery cover, take out the charging socket of battery, then connect it with the USB charger.
2. Connect the USB charger to the USB socket to charge.
3. When charging, if the temperature is slightly high, it is normal phenomenon.
4. Unpluq the charger and connection peg after using.
5. Please do not throw the battery away, or keep it away from fire and water in case of serious accident.
6. The charger is not toy. Do not allow kids to play with the charger.
7. Please check the wire, plug and other parts of the charger monthly to confirm it is in a good working condition.
8. The indicated light will be on when the power is on. The light will be flashing by flashing when it is charging. The light will be off when it is full of power. Precaution for battery safety use 1. Non -- chargeable batteries should not be charged.
2. Battery charging should be under adult's guardianship.
3. Chargeable batteries should be taken out before charging.
4. Only batteries of the same types can be used.
5. Please equip the batteries according to the right pole.
6. Batteries exhausted of power should be taken out.
7. Then connection peg should not be in short circuit. Safety caution & product maintenance 1. Please keep all accessories to avoid chilren swallowing.
2. Please change another place to play if there is severe wave interference in where you're playing.
3. Please keep the operation distance in rated meters.
4. To protect our environment, please don't litter the wrappage.
5. Please don't keep this product in where is hot or humid.
6. Please clean the battery by dry cloth if it's wet.
7. Please don't play in where is big winds and waves to avoid accident.
8. Don't wash the ship, if you want to keep the ship clcan, please use the cloth to clean it.
9. Instruction is important, it should be kept properly. Don't throw it away.
10. The ship should be installed fully, then it can be put in the warer for plaving. Trouble shooting Cannot fully charge the battery.
1. Whether the charger battery has been damaged.
2. Whether the electric outlst is damaged or something bungs it.
3. Whetherthe anode and cathode are connected well. Poor working
1. Whether the batteries of the ship controller are poor of power.
2. Whether using the recom mended batteries.
3. Whether there are obstacles between remote and ship. Dose not work at all
1. The remote control will match code with boat again.
2. Whether the power switch of the ship is turned on.
3. Whether the batteries are installed in correct way or alarm.
4. Whether the operation distance exceeds the rated distance.
5. Whether the pontes of the controller are distorted and out of contact. | 
