SQ11 Wi-Fi mini DV

SQ11 WIFI Manual. iPhone.

Charging.

Please use a 500-1000 mA charger to charge the equipment. When charging, the red indicator light is always on. When it is full, the red indicator light is off. Can work while charging.

Turn on the device.

Press the power button to start the machine. After starting the machine, the blue indicator light flashes continuously and quickly, and the device enters the state to be connected.

Note: If the blue indicator is slow flashing/always on or cannot be connected, long press the reset button for 5 seconds to reset.

Apple IOS operations are as follows:

1. Install the application.

Download and install JXLCAM. IOS searches for "JXLCAM" download directly at the Apple App Store. For convenience, please scan the download and installation of the QR code below.

Note: during installation, all permissions of the JXLCAM АРР need to be allowed, otherwise the АРР will not work properly.

Please select АPP to download.

iPhone selection

2. Local mode

Open the list of mobile phones WIFl, connect to B/xCCQ .., open the APP page after success, click "АР" as shown in the figure below, and watch the video.

Note: when there is no Wi-Fi in the environment, you can use АР mode to connect, which is valid for no more than 10m, which can achieve localized video viewing.

3. Remote mode.

1. First confirm that there is а available Wi-Fi near the device, turn on the device, flash the blue indicator light quickly, and the device is in а state to be connected. ( Note: Wi-Fi signals supported only in the 2.4G band)

2. You can't successfully distribute the network when the power is insufficient.

3. When wiring, please try to bring the device close to the router. When the nearby Wi-Fi signal is weak, the image will be stuck if the network is not successful or the network is successful.

4. Open the APP and follow these steps;

1) Click "+"

2) Click "AP add Device"

3) Click "..."

4) Click "Settings"

5) Click "WLAN"

6) Select to connect your 2,4G band Wi-Fi, and then click JXLCAM in the upper left corner to return to the АРР.

7) Enter the correct Wi-Fi password and click "Next"

8) Click "..."

9) Click "Settings"

10) Click "WLAN"

11) Connect to the device hotspot "B/XCCQ...". Then click JXLCAM in the upper left corner to return to АPP.

12) Click "Add Device"

13) Wait for distribution network

14) After seeing the success of the distribution network, click "Next".

15) Customizable name, click "Next".

16) You can view the camera preview page on the home page.

4. Home page icons and button instructions.

- Local mode

- Add device

Camera BCCQ518... - Device nickname

Online - Network status

- SD card playback file

- Manually record files

5. Description of icons and buttons on the video page.

- Settings

- Talk (Products with speakers can be used)

- Listen

- Photo

- Recording

- Landscape switching

- Alarm

- Switch left and right

- Switch up and down

- Indicator light ON/OFF

- Infrared lamp ON/OFF

- Sharpness switch

6. Storage card

If you need to store video content, you need to install an SD card.
(This machine supports loop video recording)

7. Camera settings

Name - Modify the device name

User Config - Modify user name

Move Alarm Config - Motion detection sensitivity

Note: sensitivity and alarm interval can be set for motion detection. Click "".

Share - Share the QR code to the person who needs to connect the device.

TF - Format TF card

- Restart the device

- Factory data reset

NOTE:
1. When the device fails to configure the network, please check whether the router and Wi-Fi password are configured correctly (the device does not support Wi-Fi signals in the 5.8G band). After confirming that it is correct, you can press and hold the reset button until the device indicator flashes quickly, restore the factory settings, and reconfigure network.

2. When the software homepage shows that the device is offline, you can check whether the device is normally powered on, and click the refresh icon in the upper right corner to refresh.

3. The initial password of the device is admin.

● SQ11 Wi-Fi mini DV. ►

● SQ11 Wi-Fi mini DV. Manual. Android. ►

● SQ11 mini DV. Manual. ►